touchchip usb reader stm32 driver download

#TOUCHCHIP USB READER STM32 DRIVER DOWNLOAD ZIP FILE#
#TOUCHCHIP USB READER STM32 DRIVER DOWNLOAD DRIVERS#
#TOUCHCHIP USB READER STM32 DRIVER DOWNLOAD SOFTWARE#

Type on Windows CMD (or Linux terminal) stm32flash.exe -g 0x8000000 -b 115200 -w hid_generic_pc13.bin COM2 or stm32flash -g 0x8000000 -b 115200 -w hid_generic_pc13.bin /dev/ttyS0 for programming the HID Bootloader firmware to a BluePill board.Ĭli folder contains the source code for creating the command line tool hid-flash tool.

Set BOOT-0 pin to '1' (3.3V) and reset the board.

hid_generic_pc13.bin file is for BluePill board, hid_maple_mini.bin is for Maple Mini board etc The on-board LED is connectet to the PC13 pin.

Copy into that folder the HID Bootloader file (xxx.bin) according to your board.

Extract the stm32flash to your hard disk.

Download the stm32flash from Roger's Clark Github repo.

If you connect BOOT-1 pin to 3.3V (or '1' on BluePill boards), the board will stay in HID Bootloader mode. Normally, both BOOT-0 and BOOT-1 must be connected to '0'.

Select Tools > Upload method > HID Bootloader 2.1 or newer.

Select from Arduino IDE Tools > Board >.

#TOUCHCHIP USB READER STM32 DRIVER DOWNLOAD ZIP FILE#

Apply the Arduino_STM32_patch from here in case of using Roger's Core (select the zip file according to your Operating System).

Type on Windows CMD (or Linux terminal) st-flash.exe write hid_generic_pc13.bin 0x8000000 for programming the HID Bootloader firmware to a BluePill board.

Connect BOOT-0 and BOOT-1 pins (or on-board jumpers) to GND ('0' on BluePill board).

The on-board LED is connectet to the PC13 pin. hid_generic_pc13.bin file is for BluePill board, hid_maple_mini.bin is for Maple Mini board etc. You will need the file st-flash (it is into the bin folder).

Extract the texane stlink to your hard disk.

Download the texane stlink according to your operating system (Windows, MacOSX, Linux).

Download the latest HID Bootloader release.

Installing the HID bootloader to STM32 devices (ST-Link version) The source files (Bootloader and CLI) can be compiled on Windows, Linux or Mac.įor your convenience, you can find here the hid-flash tool for these three platforms and the F1 and F4 firmware binaries. This repo is based on bootsector's stm32-hid-bootloader repository but is customized to follows the Arduino_Core_STM32 Core requirements. On STM32F4xx devices there is no point to make the bootloader much smaller than 16 KB because the first flash page is already 16 KB. This allowed for a very small bootloader 4 KB 2 KB on STM32F10x devices. Some required system files and macros have been used from ST provided SDK. It doesn't use ST libraries since they are bloated and buggy.

#TOUCHCHIP USB READER STM32 DRIVER DOWNLOAD DRIVERS#

This is a driverless (no USB drivers needed, even on Windows) USB HID bootloader

#TOUCHCHIP USB READER STM32 DRIVER DOWNLOAD SOFTWARE#

IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. THE SOFTWARE IS PROVIDED 'AS IS', WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. Under no circumstances should these files be used in relation to any critical system(s). This software is experimental and a work in progress.

Touchchip usb reader stm32 driver download